Vishay Semiconductor Diodes Division
قد تكون الصورة تمثيلية.
راجع المواصفات للحصول على تفاصيل المنتج.
2KBP10ML-5/22

2KBP10ML-5/22

Product Category: Rectifier Diode

Basic Information Overview: - Category: Electronic Component - Use: Rectification of AC to DC in electronic circuits - Characteristics: High current capability, low forward voltage drop - Package: 2-pin through-hole package - Essence: Efficient rectification of alternating current - Packaging/Quantity: Typically packaged in reels or tubes, quantity varies by manufacturer

Specifications: - Maximum Average Forward Current: 2A - Peak Repetitive Reverse Voltage: 1000V - Forward Voltage Drop: 1.1V at 2A - Operating Temperature Range: -65°C to +175°C

Detailed Pin Configuration: - Pin 1: Anode - Pin 2: Cathode

Functional Features: - Efficiently converts AC to DC - Low power loss - Fast switching capability

Advantages and Disadvantages: - Advantages: - High current capability - Low forward voltage drop - Fast switching speed - Disadvantages: - Higher cost compared to standard diodes - Sensitive to reverse voltage spikes

Working Principles: The 2KBP10ML-5/22 operates on the principle of rectification, allowing the flow of current in only one direction, effectively converting alternating current to direct current.

Detailed Application Field Plans: - Power supplies - Battery chargers - Motor drives - Inverters

Detailed and Complete Alternative Models: - 1N4007 - 1N5408 - 6A10

This comprehensive entry provides a detailed overview of the 2KBP10ML-5/22 rectifier diode, including its specifications, pin configuration, functional features, advantages and disadvantages, working principles, application field plans, and alternative models.

قم بإدراج 10 أسئلة وإجابات شائعة تتعلق بتطبيق 2KBP10ML-5/22 في الحلول التقنية

  1. What is 2KBP10ML-5/22?

    • 2KBP10ML-5/22 is a bridge rectifier diode module commonly used in power supply and rectification applications.

  2. What is the maximum voltage and current rating of 2KBP10ML-5/22?

    • The maximum voltage rating is 1000V and the maximum current rating is 2A.

  3. What are the typical applications of 2KBP10ML-5/22?

    • It is commonly used in AC to DC conversion circuits, power supplies, battery chargers, and motor drives.

  4. What is the package type of 2KBP10ML-5/22?

    • It is available in a standard 4-pin single in-line package (SIP).

  5. What are the key features of 2KBP10ML-5/22?

    • Some key features include high surge current capability, low forward voltage drop, and high isolation voltage.

  6. What are the recommended operating conditions for 2KBP10ML-5/22?

    • It is typically operated within a temperature range of -40°C to 150°C and should be mounted on a suitable heatsink for efficient heat dissipation.

  7. Can 2KBP10ML-5/22 be used in high-frequency applications?

    • Yes, it can be used in moderate to high-frequency applications due to its fast recovery time and low reverse recovery charge.

  8. Is 2KBP10ML-5/22 suitable for automotive applications?

    • Yes, it is suitable for automotive applications where reliable rectification and power conversion are required.

  9. Are there any specific precautions to consider when using 2KBP10ML-5/22?

    • It is important to observe proper polarity during installation and ensure adequate insulation to prevent electrical hazards.

  10. Where can I find detailed technical specifications and application notes for 2KBP10ML-5/22?

    • Detailed technical specifications and application notes can be found in the datasheet provided by the manufacturer or distributor of the component.